鐵藝大門在日常生活中被廣泛使用。我們走在路上基本上到處都能看到鐵藝大門的使用。關于濟南鐵藝大門相關工藝處理要點，下面我們來了解一下。

Iron gates are widely used in daily life. We can basically see the use of iron gates everywhere on the road. Now let's take a look at the processing points related to Jinan Iron Gate.

1.手工處理主要使用砂布、刮刀、錘鑿、鋼絲刷、廢砂輪等工具。并通過人工打磨、敲擊、刷洗等方式去除鐵藝護欄表面的銹皮、水垢、焊渣、灰塵等污垢。

1. Manual treatment mainly uses abrasive cloth, scraper, hammer chisel, wire brush, waste grinding wheel and other tools. The rust scale, scale, welding slag, dust and other dirt on the surface of iron guardrail shall be removed by manual grinding, knocking, brushing and other methods.

2.機械處理常用的工具有氣刷、除銹槍、拋光砂輪、氣鏟等。借助機械力的高頻沖擊和摩擦，除銹并去除水垢舊漆等污垢。

2. Common tools for mechanical treatment include air brush, derusting gun, polishing wheel, air shovel, etc. With the help of high-frequency impact and friction of mechanical force, derusting and removing scale, old paint and other dirt.

3.噴霧處理是利用機械離心、壓縮空氣、高壓水流等。作為向鐵藝護欄表面拋撒磨料、砂石、鋼丸的動力，以沖擊和磨掉氧化皮、銹跡、舊漆、型砂等。4.化學處理是用特殊配方的酸液浸泡溶解鐵藝制品，通過化學反應去除氧化皮、銹跡、油污，稱為“酸洗”。

3. Spray treatment uses mechanical centrifugation, compressed air, high-pressure water flow, etc. It is used as the power to scatter abrasives, sand and steel shot on the surface of iron guardrail to impact and grind off oxide skin, rust, old paint, molding sand, etc. 4. Chemical treatment is to soak and dissolve iron products with acid solution of special formula, and remove oxide skin, rust and oil stain through chemical reaction, which is called "pickling".

使用時間久了之后，我們會在鐵藝大門上涂上一層特殊的防銹防腐油。鐵藝大門涂一層靜電噴涂防銹油，這是一種絕緣油，有以下要求：

After a long time of use, we will apply a special layer of anti rust and anti-corrosion oil on the iron gate. The iron gate shall be coated with a layer of electrostatic spraying antirust oil, which is an insulating oil and has the following requirements:

(1)外觀應均勻透明，即無渾濁或沉淀。

(1) The appearance shall be uniform and transparent, that is, without turbidity or sediment.

(2)靜電噴涂防銹油應易帶電，常溫耐油性不低于600k，擊穿電壓不低于20kV。過小的油阻會威脅操作人員的人身安全，降低設備的安全性和可靠性，噴油霧化效果差。

(2) The electrostatic spraying antirust oil shall be easy to be electrified, the oil resistance at room temperature shall not be less than 600k, and the breakdown voltage shall not be less than 20kV. Too small oil resistance will threaten the personal safety of operators, reduce the safety and reliability of equipment, and the atomization effect of fuel injection is poor.

(3)上油是在潮濕的環境中進行的，這樣容易使水混入油中。當油中水分含量超過0.05%時，會對供油系統造成嚴重危害。此外，水容易使油變質，水分過多會使油乳化，影響涂油鋼板(帶)的防銹效果，降低油的電阻值。所以要求油中的含水量不能超過0.03%。

(3) Oiling is carried out in a humid environment, so that water can easily mix with the oil. When the water content in the oil exceeds 0.05%, it will cause serious harm to the oil supply system. In addition, water is easy to deteriorate the oil, and excessive water will emulsify the oil, affect the rust prevention effect of the oiled steel plate (strip), and reduce the oil resistance. Therefore, the water content in the oil shall not exceed 0.03%.

(4)油中殘留的懸浮或沉淀的固體雜質會造成供油管路中部件的磨損和堵塞，也影響涂油質量。如果吸油過濾器被雜質堵塞，會造成供油泵吸力不足，產生氣蝕，供油管路振動，產生噪音。

(4) The suspended or precipitated solid impurities left in the oil will cause the wear and blockage of the components in the oil supply pipeline, and also affect the oil quality. If the oil suction filter is blocked by impurities, it will cause insufficient suction of the oil supply pump, cavitation, vibration of the oil supply pipeline and noise.

如果細機油濾清器被雜質堵塞，濾芯可能會破裂，附著在濾芯上的雜質可能會進入被過濾的管路。因此，應保證油中雜質含量不大于0.005%，雜質粒徑不大于0.01mm，使供油系統的濾油器、電磁換向閥的芯棒和噴油梁的刃口狹縫不被雜質堵塞。

If the fine oil filter is blocked by impurities, the filter element may break, and impurities attached to the filter element may enter the filtered pipeline. Therefore, it shall be ensured that the content of impurities in the oil is not more than 0.005%, and the particle size of impurities is not more than 0.01 mm, so that the oil filter of the oil supply system, the mandrel of the electromagnetic reversing valve and the cutting edge slot of the fuel injection beam are not blocked by impurities.

由于應用科學，鐵藝大門廠家不易生銹腐蝕。但由于氣候的變化，酸雨的形成，不可避免的會出現生銹或腐蝕的情況，所以要多加注意它的維護保養。更多事項就來我們網站http://www.cheshifans.com咨詢！

Due to scientific application, iron gate manufacturers are not easy to rust and corrosion. However, due to climate change and the formation of acid rain, rust or corrosion will inevitably occur, so more attention should be paid to its maintenance. Come to our website for more information http://www.cheshifans.com consulting service